ไทย

Articles

Redox Reaction Basics: What Is an Electrode, and How Does an Electrochemical Cell Measure Substances in Water?

A redox reaction is a reaction in which one substance gives up electrons and another substance takes them. An electrode is an electrical conductor, such as a metal or carbon, that touches a solution and is the point where electrons move between an electrical circuit and the chemicals. When electrodes and a solution are put together as a system, the result is an electrochemical cell, the basis of batteries, electroplating and instruments that measure substances in water. This article lays out the basics of electrochemistry at the level of upper secondary school to first-year university, then shows how this knowledge is used to measure heavy metals in water.

A 3D illustration of two metal atoms passing glowing electron particles to each other against a clear water background

What is a redox reaction?

The word "redox" combines two words: reduction and oxidation.

Electrons do not simply disappear. If one substance loses electrons, another substance must take them, so oxidation and reduction always happen together. Each side is called a half-reaction.

An example you can see in the classroom

Dip a strip of zinc into blue copper sulfate solution. After a while, reddish-brown copper coats the zinc, and the blue color of the solution fades. This is the redox reaction taking place:

In this experiment the electrons pass directly at the surface of the zinc strip, so there is no electric current that can be used or measured. If the two half-reactions are separated and the electrons are made to travel through a wire, you get an electrochemical cell, explained below.

Term Meaning In the zinc and copper example
Oxidation Loss of electrons Zn → Zn²⁺ + 2e⁻
Reduction Gain of electrons Cu²⁺ + 2e⁻ → Cu
Reducing agent A substance that gives electrons to another substance and is itself oxidized Zinc
Oxidizing agent A substance that takes electrons from another substance and is itself reduced Copper ions

Redox is all around us. Iron rusting, burning and the battery in your phone are all redox reactions.

What is an electrode? Anode vs cathode

An electrode is an electrical conductor in contact with a solution that conducts electricity (called an electrolyte). At this contact surface, electrons can cross between the electrode and substances in the solution. The electrode is therefore the "gateway" that connects the world of chemical reactions to the world of electrical circuits.

Electrodes are named after the reaction that takes place on them:

Remember them as pairs: anode goes with oxidation, cathode goes with reduction. Students often ask whether the anode is positive or negative. The answer is that it depends on the type of cell. What never changes is that oxidation always happens at the anode and reduction always happens at the cathode.

The two types of electrochemical cell

An electrochemical cell has at least two electrodes in an electrolyte, plus an external circuit through which electrons flow. There are two types, depending on which way the energy flows.

Galvanic cell: a chemical reaction produces electricity

A galvanic cell, or voltaic cell, uses a redox reaction that happens on its own and makes the electrons travel through a wire from the anode to the cathode, producing electricity that can be used. The classic example is the Daniell cell, which uses the same zinc and copper reaction as the experiment above, split into two half-cells.

Under standard conditions, this cell gives a potential difference of about 1.10 volts. Every battery is a galvanic cell.

Electrolytic cell: electricity forces a reaction

An electrolytic cell works the other way around. It uses an external power supply to force a redox reaction that would not normally happen on its own. Examples include electroplating, splitting water into hydrogen and oxygen gas by electrolysis, and charging a battery.

Topic Galvanic cell Electrolytic cell
Energy Chemical → electrical Electrical → chemical
Reaction Happens on its own Must be forced by external electricity
Anode Oxidation · negative terminal Oxidation · connected to the positive terminal of the power supply
Cathode Reduction · positive terminal Reduction · connected to the negative terminal of the power supply
Examples Batteries, Daniell cell Electroplating, electrolysis of water, charging a battery

Electrochemical instruments used to test for heavy metals work in a way close to an electrolytic cell: the instrument sets the voltage to force the substance to react at the moment it chooses, then measures the current that results.

Standard electrode potential: why each metal is different

Each substance "wants electrons" to a different degree. Chemists express this as a number called the standard reduction potential, measured against the standard hydrogen electrode, which is defined as exactly 0 volts.

Half-reaction Standard reduction potential at 25 °C (volts)
Zn²⁺ + 2e⁻ → Zn (zinc) −0.76
Cd²⁺ + 2e⁻ → Cd (cadmium) −0.40
Pb²⁺ + 2e⁻ → Pb (lead) −0.13
2H⁺ + 2e⁻ → H₂ (hydrogen, reference value) 0.00
Cu²⁺ + 2e⁻ → Cu (copper) +0.34

How to read this table:

The key point for water testing is that each metal reacts at its own characteristic voltage. Electrochemical instruments therefore use the "voltage position" to tell which metal a signal comes from. The values in the table are for standard conditions. In real measurements, the signal position shifts with the type of electrode, the solution and the reference electrode used, so instruments must be calibrated against standard solutions every time.

The three electrodes in a measurement (short summary)

Most cells for measuring substances use three electrodes, each with a different job.

The control instrument connected to these three electrodes is called a potentiostat. For details of each electrode, the potentiostat and screen-printed electrodes, read What is an electrochemical sensor?

Cyclic voltammetry: the "duck-shaped" graph

Cyclic voltammetry is a basic technique electrochemists use to study redox reactions. The voltage of the working electrode is swept in one direction to a turning point, then swept back to the start, while the current is measured all the way. The result is a graph with voltage on the horizontal axis and current on the vertical axis. Its shape often looks like a duck, which is why a beginner's guide to cyclic voltammetry in the Journal of Chemical Education titled one of its sections "Understanding the 'Duck' Shape."

A 3D illustration of a closed, duck-like curve with one upper peak and one lower peak, floating above an electrode strip

Why the graph has this shape

Imagine a solution containing substance A, which can gain electrons, and sweep the voltage in the direction that causes reduction.

  1. At first, the voltage has not reached the level at which A gains electrons, so there is almost no current.
  2. When the voltage reaches A's level, the A right next to the electrode surface is reduced, and the current rises quickly.
  3. At the peak, almost all the A near the electrode surface has been used up. The layer of already-converted substance (called the diffusion layer) keeps growing thicker, so fresh A has to diffuse in from farther away. The current starts to fall, forming a peak.
  4. On the return sweep, the reduced substance near the electrode surface is oxidized back to A, forming a second peak in the opposite direction.

What you can read from the graph

What to look at What it tells you
Position of the peak on the voltage axis Which substance it is, because each substance reacts at its own voltage
Height of the peak How much of the substance there is. The Randles–Sevcik equation shows that, in a system where the substance diffuses freely and exchanges electrons quickly, the peak current is directly proportional to the concentration
Peak height when the sweep speed changes A faster sweep makes the diffusion layer thinner and the peak current higher, in proportion to the square root of the sweep speed. This is used to check whether the system follows the theory
Whether the forward and return peaks form a complete pair How reversible the reaction is

Cyclic voltammetry is well suited to "getting to know" a reaction, for example finding the voltage at which a substance undergoes redox, or testing whether a newly developed electrode works well. Measuring very small amounts of heavy metals in water usually uses a more sensitive technique, described next.

From redox reaction to measuring heavy metals in water

Once you understand redox, anodes and cathodes, the name of the technique used to test for heavy metals, "anodic stripping voltammetry," explains itself. Take cadmium as an example.

  1. Deposition step (reduction): the instrument sets the working electrode to a sufficiently negative voltage. Cadmium ions in the water gain electrons and deposit as metal on the electrode surface: Cd²⁺ + 2e⁻ → Cd. During this step the working electrode acts as a cathode.
  2. Stripping step (oxidation): the instrument gradually sweeps the voltage in the positive direction. The deposited cadmium loses electrons and returns to ions: Cd → Cd²⁺ + 2e⁻. During this step the working electrode is an anode, so the resulting current is called an "anodic current," and "stripping" means peeling the metal off the electrode surface.
  3. Reading the result: the peak position tells which metal it is, and the peak size tells how much, following the same principle as reading the graph above.

The deposition step is why this technique can detect metals at the microgram-per-liter level. For details on the equipment and the factors that affect measurement, read What is an electrochemical sensor?, and for where cadmium comes from and its limits in water, read What is cadmium? Itai-itai disease.

Basic knowledge How it is used to measure heavy metals
Redox reaction Metal ions gain electrons and deposit on the electrode, then lose electrons when they come off
Anode and cathode The working electrode is the cathode during deposition and the anode during stripping
Electrolytic cell The instrument sets the voltage to force the reaction at the moment it chooses
Different reduction potentials Each metal gives a peak at a different position, so several metals can be told apart in one measurement
Peak current proportional to concentration Comparing the peak size with a standard curve gives a concentration figure

Sensors that use this principle are classed as chemical sensors, not biosensors, because they do not use a biological component to capture the substance. Read about the differences between sensor types in What is a sensor? Biosensors and nanosensors.

How M-Sense helps

M-Sense is a portable test kit for heavy metal contamination in water that uses an electrochemical technique, developed by the National Nanotechnology Center (NANOTEC) under the National Science and Technology Development Agency (NSTDA) as part of the A-QUALITY program. The redox and electrode knowledge in this article is the foundation of this group of techniques, while what M-Sense users see is a concentration figure from the portable reader.

M-Sense tests four metals, arsenic, lead, cadmium and mercury, reports numeric results from the ppb to the ppm level, and takes about 5 minutes. It is used for screening and monitoring at the sampling point, while questionable results are sent for confirmation with standard laboratory methods. See a simulation of how it works on How M-Sense works, and the metals it detects with their limits on What it detects and the limits.

Frequently asked questions

Is the anode positive or negative? It depends on the type of cell. In a galvanic cell such as a battery, the anode is the negative terminal. In an electrolytic cell, the anode is connected to the positive terminal of the power supply. What never changes is that the anode is always the electrode where oxidation happens.

What is a redox reaction, in short? It is a reaction in which electrons are transferred from one substance to another. The substance that loses electrons is oxidized, and the substance that gains electrons is reduced. Both always happen at the same time.

What is the difference between a galvanic cell and an electrolytic cell? A galvanic cell turns chemical energy into electricity from a reaction that happens on its own. An electrolytic cell uses external electricity to force a reaction that would not happen on its own.

Why is a reference electrode needed? Because voltage must always be measured against some fixed point. The reference electrode has a constant potential, so the voltage at the working electrode is known precisely and results can be compared between measurements.

What is cyclic voltammetry used for? It is used to study redox reactions, for example to find the voltage at which a substance reacts, to see whether a reaction is reversible, and to test newly developed electrodes. Measuring small amounts of heavy metals in water usually uses the more sensitive stripping voltammetry.

How does this relate to water testing? Electrochemical heavy metal test kits use redox at the electrode surface to turn metal ions in water into a measurable electric current, which is then converted into a concentration figure.

Want to see electrochemistry at work in real water testing?

Ask NANOTEC · How M-Sense works · What is an electrochemical sensor?

References

NANOTEC, NSTDA assistantAnswers are based on NANOTEC information. Questions it cannot answer are passed to the team.

Privacy policy

The M-Sense website and its question-answering assistant are operated on behalf of the National Nanotechnology Center (NANOTEC), NSTDA.

Data collected: the messages you type in the chat and the contact details you enter yourself, such as name, organization, position, province, phone number and email. If you chat through LINE, the system sees your LINE display name and profile picture.

Used for: answering questions, passing your request to the NANOTEC team, contacting you back and improving the answers. Not used for other marketing, and never sold.

Automatic answers are generated by an artificial intelligence system, so chat messages are processed by AI and cloud service providers, which may be located outside Thailand.

Who sees the data: NANOTEC staff who handle inquiries and the website administrators.

You can ask to see, correct or delete your data through the "Ask NANOTEC" button or LINE @nanotec.