What Is ppm? What Is ppb? How to Read a Water Test Result
What is ppm? ppm means "parts per million", and ppb means "parts per billion". For ordinary water, 1 ppm is about 1 milligram per liter, and 1 ppb is about 1 microgram per liter. Whatever method is used to test water quality, heavy metal results are usually reported in these units. Once you can convert between them, you can compare a water test result with the right limit. For example, the arsenic limit for drinkable tap water, 0.01 milligrams per liter, equals 10 ppb.

Why units matter
The same water test result can be written in several ways. Laboratory reports in Thailand usually use milligrams per liter (mg/L). World Health Organization (WHO) guidelines are often written in micrograms per liter. Many field test kits show results in ppb or ppm.
These numbers refer to the same quantity in different units. Misread the unit and the number can be off by as much as 1,000 times. For example, 10 ppb and 10 ppm differ by a factor of 1,000, even though the numbers look the same.
What is ppm?
ppm stands for parts per million: the substance of interest makes up 1 part in a total mixture of 1,000,000 parts.
In water, 1 ppm is roughly 1 milligram per liter. The reason is that 1 liter of water weighs about 1 kilogram, or 1,000,000 milligrams. If 1 milligram of a substance is dissolved in it, that is exactly 1 part per million.
ppm is often used for substances present in fairly large amounts, such as dissolved solids. Thailand's Department of Health criteria for drinkable tap water (2020) set dissolved solids at not more than 500 milligrams per liter, or about 500 ppm.
What is ppb?
ppb stands for parts per billion, 1,000 times smaller than ppm. In water, 1 ppb is roughly 1 microgram per liter (µg/L); 1 microgram is one-thousandth of a milligram.
Heavy metals in drinking water have very low limits, so they are often expressed in ppb because it is easier to read. For example, the mercury limit for drinkable tap water, 0.001 milligrams per liter, is easier to grasp as 1 ppb than as a number with three decimal places.
ppm vs ppb: unit conversion table
| Unit | Full name | Equivalent in water | Example |
|---|---|---|---|
| ppm | parts per million | ≈ 1 milligram per liter | 0.3 ppm ≈ 0.3 mg/L |
| ppb | parts per billion | ≈ 1 microgram per liter | 10 ppb ≈ 10 µg/L |
| mg/L | milligrams per liter | = 1,000 micrograms per liter | 0.01 mg/L = 10 µg/L |
| ppm and ppb | 1 ppm = 1,000 ppb | 0.003 ppm = 3 ppb |
Easy ways to convert mg/L to ppm and ppm to ppb
- From milligrams per liter (or ppm) to ppb: multiply by 1,000. For example, 0.01 × 1,000 = 10 ppb.
- From ppb to milligrams per liter (or ppm): divide by 1,000. For example, 3 ÷ 1,000 = 0.003 mg/L.
- Tip: multiplying by 1,000 moves the decimal point 3 places to the right; dividing by 1,000 moves it 3 places to the left.
Good to know
This ppm-to-milligrams-per-liter equivalence works for water with a density of about 1 gram per milliliter, such as drinking water, tap water and ordinary surface water. The U.S. Geological Survey (USGS) and the U.S. Environmental Protection Agency (US EPA) use the same equivalence. Thick or very salty liquids need a more detailed calculation.
Limits for 4 heavy metals, written in ppb
This table converts limits given in milligrams per liter into ppb for easy comparison. Always check the column heading to see which kind of water the limit applies to.
| Substance | Drinkable tap water, Thailand's Department of Health (2020) | Surface water, Notification No. 8 (1994) | WHO drinking water guideline value |
|---|---|---|---|
| Arsenic | 0.01 mg/L = 10 ppb | 0.01 mg/L = 10 ppb | 10 µg/L (provisional) |
| Lead | 0.01 mg/L = 10 ppb | 0.05 mg/L = 50 ppb | 10 µg/L (provisional) |
| Cadmium | 0.003 mg/L = 3 ppb | 0.005 mg/L = 5 ppb (water with hardness not more than 100 mg/L) · 0.05 mg/L = 50 ppb (above 100 mg/L) | 3 µg/L |
| Mercury | 0.001 mg/L = 1 ppb | 0.002 mg/L = 2 ppb | 6 µg/L (inorganic mercury, 2022 edition) |
All values are "not more than" values, and they apply to different kinds of water:
- Tap water used for drinking uses Thailand's Department of Health criteria for drinkable tap water (2020).
- Water in rivers and canals uses Thailand's surface water quality standards (National Environment Board Notification No. 8, 1994). These values are for assessing raw water sources; they do not mean the water is drinkable.
- WHO values are international guideline values for drinking water. The arsenic value of 10 micrograms per liter is a "provisional" value set with the capability of water treatment and measurement in mind.
A caution: the Department of Health's current arsenic limit for drinking water is 0.01 milligrams per liter (10 ppb). Some sources still cite 0.05 milligrams per liter, which comes from an older set of criteria and should not be used to judge drinking water today.

Reading a water test result, step by step
When you have a result, go through these 4 steps:
- Check the unit: is the result in ppm, ppb, milligrams per liter or micrograms per liter?
- Convert it to the same unit as the limit, by multiplying or dividing by 1,000 as above.
- Choose the limit that matches the type of water: tap water used for drinking, or water in a surface water source.
- Compare, and see how far from the limit the result is. To find out how many times over the limit it is, divide the measured value by the limit in the same unit.
Hypothetical example 1: below the limit
Hypothetical example: tap water used for drinking is tested and shows arsenic at 4 ppb.
- Convert: 4 ppb = 0.004 mg/L
- Drinkable tap water limit: 0.01 mg/L (10 ppb)
- Reading: not above the limit; the measured value is less than half the limit.
Hypothetical example 2: above the limit
Hypothetical example: tap water used for drinking is tested and shows arsenic at 0.025 mg/L.
- Convert: 0.025 mg/L = 25 ppb
- Drinkable tap water limit: 10 ppb
- Reading: above the limit, 25 ÷ 10 = 2.5 times. The result should be confirmed by standard laboratory methods, and the agency managing the local water supply system should be informed.
Hypothetical example 3: choosing the wrong set of limits
Hypothetical example: river water is tested and shows lead at 30 ppb (0.03 mg/L).
- Compared with the surface water limit (50 ppb), this value is not above the surface water limit.
- But if this water is to be used to produce tap water, the tap water produced must contain not more than 10 ppb of lead under the drinkable tap water criteria, which is lower than 30 ppb.
- This example shows that the same number can be read differently depending on the kind of water.
Hypothetical example 4: misreading the unit
Hypothetical example: the screen shows arsenic as "8" in ppb, but it is written down in a notebook as 8 ppm.
- 8 ppb = 0.008 mg/L, not above the drinkable tap water limit.
- 8 ppm = 8 mg/L, 800 times the limit.
- The same number with a different unit means something very different, so always record the unit.
A real-data example: before and after upgrading a water supply system
In NANOTEC's work on upgrading a village water supply system at Ban Rim Kok, Mae Yao Subdistrict, Mueang Chiang Rai District (northern Thailand), arsenic in the raw water measured 0.069 milligrams per liter, and dropped to 0.0035 milligrams per liter at the elevated water tower after treatment.
| Sampling point | mg/L | ppb | Compared with the drinkable tap water limit of 10 ppb |
|---|---|---|---|
| Raw water before treatment | 0.069 | 69 | About 6.9 times the limit |
| Elevated water tower after treatment | 0.0035 | 3.5 | Below the limit |
Converting to ppb makes the picture clearer: the raw water contained 69 ppb of arsenic, but after treatment only 3.5 ppb remained, below the 10 ppb limit. This example also shows that the raw water figure is used to decide that treatment is needed, while the figure after treatment is used to confirm that the system works.
How to record water test results so they stay useful
A single test tells you only about that day, but when results are recorded systematically, several tests can show a trend. Record at least:
- The date and time the sample was taken
- The sampling point, such as raw water, the elevated water tower, or a tap at the end of the line
- The type of water: surface water, groundwater or tap water
- The measured value, always with its unit
- The test method: field test kit or laboratory
- The limit used for comparison, and the result of the comparison
If values are always recorded in the same unit, for example all in ppb, it is easy to compare each test and see at once whether values are rising or falling.
Other units in water test results
Not every item in a water test result uses ppm or ppb.
- Turbidity uses NTU (nephelometric turbidity units), a unit specific to turbidity, not an amount of substance per liter, so it does not need converting to ppm. The Department of Health's drinkable tap water limit is not more than 5 NTU.
- Electrical conductivity (EC) uses an electrical unit, not ppm. NANOTEC's drinking water production system shows this value together with total dissolved solids (TDS) on a real-time display.
- Coliforms and E. coli: the drinkable tap water criteria require them to be "not detected", so the result is read as detected or not detected.
How M-Sense helps
M-Sense, the portable heavy metal test kit for water from the National Nanotechnology Center (NANOTEC), NSTDA, reports numerical results in the ppb to ppm range for 4 heavy metals: arsenic, lead, cadmium and mercury. Each test takes about 5 minutes on a portable reader at the sampling point. With a number in hand, officers can compare it with the limit straight away using the method in this article, and see how close to or above the limit the value is. M-Sense is used for screening and monitoring; suspicious results are sent for confirmation by standard laboratory methods.
See the principle on the page How M-Sense works, and compare different testing methods in the article Water quality testing: 3 methods.
Frequently asked questions
What is ppm, and how many milligrams per liter is it? ppm means parts per million. In ordinary water, 1 ppm is about 1 milligram per liter.
How many ppb are in 1 ppm? 1 ppm equals 1,000 ppb, because ppb is a unit 1,000 times smaller than ppm.
What is the arsenic limit for drinking water in ppb? Thailand's Department of Health criteria for drinkable tap water (2020) set arsenic at not more than 0.01 milligrams per liter, which equals 10 ppb and matches the WHO guideline value of 10 micrograms per liter.
Why is the lead limit for rivers (50 ppb) higher than for tap water (10 ppb)? Because they are limits for different kinds of water. The surface water standard is used to assess raw water in rivers and canals, while the drinkable tap water criteria apply to water that has been treated and will be drunk.
What does µg/L on a test report mean? µg/L means micrograms per liter. In water it is about equal to ppb; for example, 3 µg/L is about 3 ppb.
What should I do if a measured value is close to the limit? Test again to see the trend. If a result is above the limit or suspicious, confirm it with standard laboratory methods and inform the agency responsible for the water source or the local water supply system. For health concerns, contact a subdistrict health promoting hospital (Thailand's local primary care unit) or the local public health office.
Want to know what the water test results in your area mean?
Ask NANOTEC · What it detects, and the limits
References
- Bureau of Laboratory, Department of Health, Thailand. Criteria for drinkable tap water, Department of Health, 2020 (document SD-RLDC-006).
- National Environment Board Notification No. 8 (1994) on surface water quality standards, Thailand.
- World Health Organization. Guidelines for drinking-water quality, 4th edition incorporating the first and second addenda, 2022.
- World Health Organization. Chemical fact sheets: Arsenic, Lead (2022), Cadmium, Mercury (2022).
- U.S. Geological Survey. Conversion factors.
- U.S. Environmental Protection Agency. Drinking water guidance documents (units mg/L and µg/L).
- National Nanotechnology Center. Report on the use of technology to solve water quality problems and improve community access to clean water.
- National Nanotechnology Center. Arsenic management innovation for sustainable clean tap water production.
- National Nanotechnology Center. Portable electrochemical test kit for heavy metal contamination in water (M-Sense).
